VPrime pod resistance guide
| Resistance | Wattage range | Vaping style | Best e-liquid |
|---|---|---|---|
| 0.2 ohm | 40-60W | DTL — direct to lung, large clouds | High VG 70/30 shortfill |
| 0.4 ohm | 25-40W | RDTL — restricted direct to lung | 70/30 or 60/40 freebase |
| 0.6 ohm | 15-25W | Loose MTL — smooth with good vapour | 50/50 freebase or nic salt |
| 0.8 ohm | 10-18W | Tight MTL — cigarette-style draw | 50/50 nic salt 10mg or 20mg |
Available variants
Standard 2ml pods (pack of 2)
| Pod | Resistance |
|---|---|
| VPrime 2ml 0.4 ohm — 2 pack | 0.4 ohm |
| VPrime 2ml 0.6 ohm — 2 pack | 0.6 ohm |
XL pods (pack of 2)
| Pod | Resistance |
|---|---|
| VPrime XL 0.2 ohm — 2 pack | 0.2 ohm |
| VPrime XL 0.4 ohm — 2 pack | 0.4 ohm |
| VPrime XL 0.6 ohm — 2 pack | 0.6 ohm |
| VPrime XL 0.8 ohm — 2 pack | 0.8 ohm |
About OXVA VPrime replacement pods
VPrime pods use UniTech 2.0 mesh coils — the same coil technology used across the OXVA NeXlim range. Cotton fibres are wrapped around the mesh coil in a specific arrangement designed for rapid e-liquid absorption and even heating across the full coil surface. OXVA claims this delivers up to 50% more flavour and 45% more vapour compared to earlier single-element coil designs, with a 30% longer coil lifespan. Each pod replaces as a complete unit when the coil wears out — there are no separate coil heads to buy.
The 5-layer leak-proof structure uses triple silicone seals and a sealed airflow path that prevents e-liquid reaching the device contacts. The side fill port is accessed by lifting a silicone plug on the side of the pod — fill, reseat the plug and the pod is sealed. A transparent pod body lets you monitor e-liquid level without removing the pod. VPrime pods connect magnetically to the device and are not physically compatible with any other OXVA device including Xlim, NeXlim and Oneo kits.
How to fill VPrime pods
- Leave the pod in the VPrime device — it does not need to be removed to refill
- Locate the silicone plug on the side of the pod
- Lift the silicone plug to expose the fill port
- Insert the nozzle of your e-liquid bottle and squeeze gently to fill
- Reseat the silicone plug firmly to seal the port
- Allow the coil to prime for 5 to 10 minutes before vaping — especially important for a fresh pod at the 0.2 ohm
Buy OXVA VPrime pods from e-liquids.com
- VPrime pods in stock across all four resistances in standard and XL variants
- Genuine OXVA pods — UniTech 2.0 mesh coils, 5-layer leak-proof
- Free UK delivery on all orders over £20
- Same-day dispatch on orders placed before cut-off
- UK-based customer team on 0121 272 2900
OXVA VPrime replacement pods: frequently asked questions
Which VPrime pod should I use for nic salts?
For nic salts use the 0.8 ohm pod for a tight MTL draw at 10 to 18W, or the 0.6 ohm for a slightly looser draw at 15 to 25W. Both work well with 50/50 nic salt e-liquids at 10mg or 20mg. The 0.2 ohm and 0.4 ohm pods are designed for DTL and RDTL vaping with higher VG freebase e-liquids at higher wattages and are not suitable for full-strength nic salts.
Are VPrime pods compatible with any other OXVA device?
No. VPrime pods are designed exclusively for the OXVA VPrime pod kit. They are not compatible with any Xlim device (Go, Go 2, Pro 2, Pro 3, 3 Ultra, SQ Pro 2), the NeXlim, the NeXlim Go or the Oneo. Each OXVA device uses its own dedicated pod format.
How long do VPrime pods last?
Most VPrime pods last one to two weeks depending on how much you vape, the wattage you use and the e-liquid type. The 0.2 ohm pod used at 60W for DTL vaping will deplete faster than the 0.8 ohm used at low wattage for MTL. Replace the pod when you notice the flavour becoming muted, burnt or noticeably weaker than when the pod was fresh.